ykwong71 blogger: November 2020

reference:ftp://ftp.dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_networking/esuprt_net_fxd_prt_swtchs/powerconnect-6248_user%27s%20guide_en-us.pdf

google search for user guide Powerconnect 6248

Download Putty (just put com port number also can connect to USB or Serial Port ) then connect to Dell Powerconnect

after connect Putty then Reset the Powerconnect wait until booting you can set Putty console

Example of an Easy Setup Wizard Session
This section describes an Easy Setup Wizard session. See the state diagram (Figure 5-2) for the general
flow. The values used by the following session are examples only. Please request the actual values from
your network adminstrator(s):
• IP address for the management VLAN is 192.168.2.1:255.255.255.0.
• The user name is admin, and password is password.
• The network management system IP address is 192.168.2.1.
• The default gateway is 192.168.1.1.
• The SNMP community string to be used is public
The setup wizard configures the initial values as defined above. After you complete the wizard, the
system is configured as follows:
• SNMPv1/2c is enabled and the community string is set up as defined above. SNMPv3 is disabled.
• The admin user account is set up as defined.
• A network management system is configured. From this management station, you can access the
SNMP, HTTP, and CLI interfaces. You may also choose to allow all IP addresses to access these
management interfaces by choosing the (0.0.0.0) IP address.
• An IP address is configured for the default management VLAN (1).
• A default gateway address is configured.
NOTE: In the example below, the possible user options are enclosed in [ ]. Also, where possible, the default value is
provided in { }. If you enter <Return> with no options defined, the default value is accepted. Help text is in
parentheses.
The following example contains the sequence of prompts and responses associated with running an
example Dell Easy Setup Wizard session, using the input values listed above.
Unit 1 - Waiting to select management unit)>
Applying Global configuration, please wait ...
Welcome to Dell Easy Setup Wizard
The Setup Wizard guides you through the initial switch configuration,
and gets you up and running as quickly as possible. You can skip the
setup wizard, and enter CLI mode to manually configure the switch. You
must respond to the next question to run the setup wizard within 60
seconds, otherwise the system will continue with normal operation using
the default system configuration. Note: You can exit the setup wizard
at any point by entering [ctrl+z].
Would you like to run the setup wizard (you must answer this question
within 60 seconds)? [Y/N] y

Step 1:
Configuring Dell PowerConnect 85
The system is not setup for SNMP management by default. To manage the
switch using SNMP (required for Dell Network Manager) you can:
o Set up the initial SNMP version 2 account now.
o Return later and setup other SNMP accounts. (For more information on
setting up an SNMP version 1 or 3 account, see the user documentation).
Would you like to setup the SNMP management interface now? [Y/N] y
To setup the SNMP management account you must specify the management
system IP address and the "community string" or password that the
particular management system uses to access the switch. The wizard
automatically assigns the highest access level [Privilege Level 15] to
this account. You can use Dell Network Manager or other management
interfaces to change this setting, and to add additional management
system later. For more information on adding management systems, see
the user documentation.
To add a management station:
Please enter the SNMP community string to be used.
{public}:
public<Enter>
Please enter the IP address of the Management System (A.B.C.D) or
wildcard (0.0.0.0) to manage from any Management Station.
{0.0.0.0}:
192.168.2.1<Enter>

Step 2:
Now we need to setup your initial privilege (Level 15) user account.
This account is used to login to the CLI and Web interface. You may
setup other accounts and change privilege levels later. For more
information on setting up user accounts and changing privilege levels,
see the user documentation.
To setup a user account:
Please enter the user name: admin<Enter>
Please enter the user password: ********<Enter>
Please reenter the user password: ********<Enter>
Step 3:
86 Configuring Dell PowerConnect
Next, an IP address is setup. The IP address is defined on the default
VLAN (VLAN #1), of which all ports are members. This is the IP address you
use to access the CLI, Web interface, or SNMP interface for the switch.
Optionally you may request that the system automatically retrieve an IP
address from the network via DHCP (this requires that you have a DHCP
server running on the network).
To setup an IP address:
Please enter the IP address of the device (A.B.C.D) or enter "DHCP"
(without the quotes) to automatically request an IP address from the
network DHCP server.
192.168.2.1<Enter>
Please enter the IP subnet mask (A.B.C.D or /nn):
255.255.255.0<Enter>
Step 4:
Finally, set up the gateway. Please enter the IP address of the gateway
from which this network is reachable
192.168.1.1<Enter>
This is the configuration information that has been collected:
SNMP Interface = "public"@192.168.2.1
User Account setup = admin
Password = **********
Management IP address = 192.168.2.1 255.255.255.0
Gateway = 192.168.1.1
Step 5:
If the information is correct, please select (Y) to save the
configuration, and copy to the start-up configuration file. If the
information is incorrect, select (N) to discard configuration and
restart the wizard: [Y/N]
y<Enter>
Thank you for using the Dell Easy Setup Wizard. You will now enter CLI
mode.
.....
console>

Enable <enter>

show vlan <enter>

tftp server

https://www.youtube.com/watch?v=YdVEonLMWYs

Destination put Running-config.txt

Startup-config.txt

https://www.dell.com/downloads/global/products/pwcnt/en/pwcnt_stacking_switches.pdf

ykwong71 blogger

Monday, 30 November 2020

Malware Traffic Analysis

Free Cam

Sunday, 29 November 2020

Dell Powerconnect 6248 Putty Console 1.Operational Code and 2. Boot Menu

Dell Powerconnect 6248 Console Show Vlan

Dell Powerconnect 6248 Get Started